Design Aspects of Lower Limb Exoskeleton

Arunkumar      S; Sarath      M

Abstract

Aim: This research work aimed at the design, simulation, and validation of a lower limb exoskeleton for rehabilitation. The device can provide regressive gait training for patients suffering from lower limb mobility disorders.

Background: People suffering from mobility disorders, such as spinal cord injuries, and other related diseases are in high proportion. Exoskeletons play a vital role in enhancing the lifestyle of people with disorders. Devices that provide locomotion assistance and help in reducing the burden of therapists through effective and repetitive gait training are in high demand. Exoskeletons have further extended to the fields of the military to enhance the performance of physically abled persons. Prototype development of lower limb exoskeletons is too expensive and many of them are patented. The requirement for this system to perform human trials is subjective to several medical and ethical norms. Thus, there exists a need to evaluate and validate the exoskeleton designs.

Methods: In this work, the design has been made inclusive of different body shapes and sizes. The device has been modeled in SOLIDWORKS and its structural integrity has been analyzed using the ANSYS software. Later, the model has been subjected to environmental assessment and then motion analysis using the ADAMS software.

Results: The structural integrity analysis has revealed the design to be adequate to carry the applied load as the stresses induced were less than the yield strength of the material. The sustainability analysis showed that LLE made of aluminium alloy had less impact on the environment relative to the other two materials.

Conclusion: The kinematic simulation revealed that the angular amplitudes, the reaction force of the right hip and knee joint, and the contact force between the shoe and the ground of the exoskeleton agreed well with the experimental findings of the literature.

Keywords: Lower limb exoskeleton, gait training, simulation, sustainability, rehabilitation, modeling.

[1]
W. H. Organization and, I.S. C. Society. International perspectives on spinal cord injury. World Health Organization 2013.

[2]
Bernhardt M, Frey G, Riener R. Hybrid force-position control yields cooperative behaviour of the rehabilitation robot lokomat. 9th Int Conf Rehabil Robot.  536-9.

[3]
Gong C, Chow Khuen C, Guo Z, Haoyong Yu. A review of lower extremity assistive robotic exoskeletons in rehabilitation therapy. Crit Rev Biomed Eng  2013; 41(4-5): 343-63.

[4]
Vokubratovic M. Legged Locomotion Robots and Anthropomorphic Mechanisms. MIHAILO PUPIN INSTITUTE 1975.

[5]
Rupal BS, Rafique S, Singla A, Singla M, Virk GS. Lower-limb exoskeletons: Research trends and regulatory guidelines in medical and non-medical applications. Int J Adv Robot Syst  2017; 14: 1729881417743554.

[6]
Carvey Mathey R. Metabolically efficient leg brace. US20050251079A1, 2005.

[7]
ROM Robotics Inc. Lower leg exosekelton system and method. US11213417B2, 2022.

[8]
Wu M, Hornby TG, Landry JM. A cable-driven locomotor training system for restoration of gait in human. Gait Posture  2011; 33(2): 256-60.
 [http://dx.doi.org/10.1016/j.gaitpost.2010.11.016] [PMID: 21232961]

[9]
Hussain S, Xie SQ, Jamwal PK, Parsons J. An intrinsically compliant robotic orthosis for treadmill training. Med Eng Phys  2012; 34(10): 1448-53.
 [http://dx.doi.org/10.1016/j.medengphy.2012.02.003] [PMID: 22421099]

[10]
Park HS, Ren Y, Zhang LQ. IntelliArm: An exoskeleton for diagnosis and treatment of patients with neurological impairments. Proceeding of the 2nd IEEE RAS & EMBS International Conference on Biomedical Robotics and Biomechatronics,. Scottsdale, AZ, USA October 19–22,. 2008: 109–114.

[11]
Stegall P, Winfree K, Zanotto D. Rehabilitation exoskeleton design: Exploring the effect of the anterior lunge degree of freedom. IEEE Trans Robot  2013; 29(4): 825-37.

[12]
Li J, Zhang Z, Tao C, Ji R. Structure design of lower limb exoskeletons for gait training. Chin J Mech Eng  2015; 28(5): 878-87.
 [http://dx.doi.org/10.3901/CJME.2015.0525.075]

[13]
Nimje AA, Patil AP, Sakhare DY. Design of lower limb exoskeleton. Lect Not Netw Sys  2021; 154: 431-9.
 [http://dx.doi.org/10.1007/978-981-15-8354-4_43]

[14]
Luis IM, Fabian AS, Kenneth PB, Andres VR. Mechatronic Design of Lower Limb Exoskeleton, Design, Control and Applications of Mechatronic Systems in Engineering.  Intech publishers 2017; pp. 112-34.

[15]
Luis IM, Anthony JV, Jonathan MB. Low cost lower limb exoskeleton for assisting gait rehabilitation: Design and evaluation. Czech Republic Association for Computing MachineryACM, Prague,. ICACR  2019 October 11–13, 2019. 

[16]
Pirjade YM, Kotkar AU, Londhe DR, Shelke TP. Design and fabrication of a low-cost human body lower limb exoskeleton. IEEE 6th Int Conf Mechatr Robot Eng  32-7.

[17]
Kim JH, Jeong WH, Yoon SB. Design of a walking assistance lower limb exoskeleton for paraplegic patients and hardware validation using CoP. Int J Adv Robot Syst  2013; 10(113): 1-13.

[18]
Yu S, Han C, Cho I. Design considerations of a lower limb exoskeleton system to assist walking and load-carrying of infantry soldiers. Appl Bionics Biomech  2014; 11(3): 119-34.
 [http://dx.doi.org/10.1155/2014/585837]

[19]
Atmaja R, Munadi ANDT. Stress analysis of lower limb exoskeleton for walking assistance using finite element method. Int J Appl Eng Res  2017; 12(13): 3864-6.

[20]
Jiménez-Armendáriz J, Jimenez-Martinez M, Varela-Soriano J, Santana Diaz A, Perez Santiago R. Energy dissipation enhancement of thin-walled 6063 T5 aluminium tubes by combining a triggering mechanism and heat treatment. Metals  2023; 13(5): 922.
 [http://dx.doi.org/10.3390/met13050922]

[21]
Tang J, Li X, Zhang G, et al. An ANSYS/LS-DYNA simulation and experimental study of sectional hob type laver harvesting device. Agriculture  2023; 13(2): 361.
 [http://dx.doi.org/10.3390/agriculture13020361]

[22]
Antony KM, Arunkumar S. DFMA and sustainability in product design. J Phys Conf Ser  2020; 1455: 012028.
 [http://dx.doi.org/10.1088/1742-6596/1455/1/012028]

[23]
Subbaiah A, Antony KM. Integration of DFMA and sustainability: A case study. Int J Sustain Eng  2021; 14(3): 343-56.
 [http://dx.doi.org/10.1080/19397038.2020.1871443]

[24]
Wu C-H, Mao H-F, Hu J-S. The effects of gait training using powered lower limb exoskeleton robot on individuals with complete spinal cord injury. J Neuroeng Rehabil  2018; 15: 1-10.

[25]
Copilusi C, Ceccarelli M, Carbone G. Design and numerical characterization of a new leg exoskeleton for motion assistance. Robotica  2015; 33(5): 1147-62.
 [http://dx.doi.org/10.1017/S0263574714002069]

[26]
Harold A. Rothbart, CAM Design Handbook. The McGraw-Hill Companies, Inc. 2004.

[27]
Niaam Kh. Investigation of vertical ground reaction force during walking with the exoskeleton for patient with unilateral lower limb weakness. Proceedings of 2nd International Multi-Disciplinary Conference Theme: Integrated Sciences and Technologies, IMDCIST 2021 7-9 September  2021,.  Sakarya, Turkey.
 [http://dx.doi.org/10.4108/eai.7-9-2021.2314896]

[28]
Yang N, Dai S. Human body gait movement simulation based on adams. Mech Eng Autom  2015; 6: 56-7.

Cite As

Recent Patents on Mechanical Engineering

Design Aspects of Lower Limb Exoskeleton

Abstract